Zoom HD8 Installationsanleitung PDF herunterladen (Seite 5)

Cubase LE 4 Installation Guide/ Control Surface Operation Guide

Cubase LE 4 Installation Guide/Control Surface Operation Guide

This section describes use of the HD8/HD16 when the unit is

switched to control surface mode.

When the HD8/HD16 is switched to control surface mode and

Mackie Control has been selected as operation mode, the keys

and faders of the HD8/HD16 can be used to remotely control

the transport and mixing functions of Cubase LE 4.

When you switch the HD8/HD16 to control surface mode and

select Mackie Control as operation mode, the display

indication changes as follows.

In control surface mode, the HD8/HD16 recorder functions are

not available, and the knobs and keys on the panel have special

functions for Cubase LE 4. The level meters of the HD8/HD16

show the fader positions for the Cubase LE 4 tracks.

For a list of functions assigned to the keys and knobs of the

HD8/HD16 in Mackie Control mode, see the table "Control

surface mode functions at a glance" on page 8 of this

document.

When the HD8/HD16 is in control surface mode (operation

mode: Mackie Control), the keys of the transport section

control the following Cubase LE 4 functions.

Regarding the Cubase LE 4 functions of other keys in the

function/transport section, see the table "Control surface mode

functions at a glance" on page 8 of this document.

When the HD8/HD16 is in control surface mode (operation

mode: Mackie Control), the fader section controls (faders,

status keys, parameter knobs) can be used to adjust major

parameters of Cubase LE 4.

NOTE

With the HD8, the [RHYTHM] fader, [RHYTHM] status key, and

[RHYTHM] parameter knob can also be used, but with the

HD16, these controls are "not assigned".

A group of tracks operated by the fader section controls

(faders, status keys, parameter knobs) is called a "bank".

In Mackie Control mode, one bank can comprise up to 8 tracks.

For example, if fader 1 is assigned to track 1 of Cubase LE 4,

tracks 1 to 8 will be assigned as listed in the tables below.

●

HD8

●

HD16

The following keys can be used to change the track (channel)

assignment of the fader section controls.

●

[AUTO PUNCH IN/OUT] key (<CHANNEL)

Shifts the track (channel) assignment of the fader section

controls one position back.

● [A-B REPEAT] key (CHANNEL>)

Shifts the track (channel) assignment of the fader section

controls one position forward.

For example, if tracks 1 to 8 are currently assigned as shown

in the tables above, pressing the [A-B REPEAT] key

(CHANNEL>) once will change the assignment as listed in the

tables below, so that tracks 2 - 9 are now assigned.

● HD8

● HD16

● [TRACK PARAMETER] key (<BANK)

Shifts the track (channel) assignment of the fader section

controls back by 8 tracks.

Using the control surface

mode

About the control surface mode

Operating the transport

CUBASE

:Rec

FF [Y] key

Fast forward

REW [T] key

Rewind

STOP [P] key

Stop

PLAY [R] key

Play

REC [O] key

Record

About banks

Fader

1 2 3 4 5 6 7/8 [RHYTHM]

Controlled

track

Tr. 1 Tr. 2 Tr. 3 Tr. 4 Tr. 5 Tr. 6 Tr. 7 Tr. 8

Fader

1 2 3 4 5 6 7 8

Controlled

track

Tr. 1 Tr. 2 Tr. 3 Tr. 4 Tr. 5 Tr. 6 Tr. 7 Tr. 8

Fader

1 2 3 4 5 6 7/8

[RHYTHM]

Controlled

track

Tr. 2 Tr. 3 Tr. 4 Tr. 5 Tr. 6 Tr. 7 Tr. 8 Tr.9

Fader

1 2 3 4 5 6 7 8

Controlled

track

Tr. 2 Tr. 3 Tr. 4 Tr. 5Tr. 6Tr. 7Tr. 8Tr.9

1 2 3 4 5 6 7 8 9 10 ... 15 16

Kommentare zu diesen Handbüchern

Keine Kommentare

Zoom HD8 Installationsanleitung Seite 5

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Musikinstrumente Zoom HD8