Zoom MAC Bedienungsanleitung

MAC 401 DualMAC 401 CT Zoomuser manualTMTM

10 MAC 401™ user manualData linkA data link is required in order to control a MAC 401 via DMX.The MAC 401 has 5-pin locking XLR connectors for DMX da

Physical installation 11Physical installationThe MAC 401 can be placed on a horizontal surface such as a stage or clamped to a truss in any orientati

12 MAC 401™ user manualSetupWarning! Read “Safety Information” on page 3 before installing, powering, operating or servicing the MAC 401.Control pane

Setup 13• The SERVICE LED lights if the fixture requires a service intervention. At the same time, a message appears in the display indicating the ty

14 MAC 401™ user manualWhether one or two LED modules are installed on a fixture, all modules’ DMX addresses must be set manually using the ADDR menu

Setup 15DMX channels used by RGB Zoom moduleThe following table gives an overview of the control menu settings available and number of DMX channels u

16 MAC 401™ user manualDMX channels used by CT Zoom moduleThe following table gives an overview of the control menu settings available and number of

Setup 17Whatever cooling mode is selected, a thermal cutout shuts down power to the LEDs if the fixture temperature exceeds safe limits. If this occu

18 MAC 401™ user manualEffectsMAC 401 – all modelsThis section describes the lighting effects available in all currently available models of the MAC

Effects 19words, output is very slightly lower than absolute maximum output to allow a margin for adjustment, and LED modules are individually calibr

DimensionsAll dimensions are in millimeters©2009-20010 Martin Professional A/S. Information subject to change without notice. Martin Professional A/S

20 MAC 401™ user manualService and maintenanceWarning! Read “Safety Information” on page 3 before servicing the MAC 401.Warning! Disconnect the fixtu

Service and maintenance 21Warning! Disconnect from power and allow to cool before cleaning.To clean the fixture:1. Disconnect the fixture from power

22 MAC 401™ user manualControl menu service utilitiesFixture resetThe RST command in the MAN menu resets the fixture and can be used as a first remed

Service and maintenance 23Fixture readoutsDMX input signalThe DMXL menu lets you view the DMX values received on each channel. If the fixture does no

24 MAC 401™ user manualDiagnostic feedbackIf an error occurs, one of the following messages may appear in the MAC 401 display:Message Cause... What t

DMX protocols 25DMX protocolsTwo DMX protocols are given below: for the MAC 401 RGB Zoom module and CT Zoom module.Certain channels in the CT Zoom mo

26 MAC 401™ user manual—30 - 1920 - 3940 - 5960 - 7980 - 8485 - 8990 - 9495 - 99100 - 104105 - 109110 - 114115 - 119120 - 124125 - 129130 - 134135 -

DMX protocols 27—70 - 1920 - 3940 - 5960 - 7980 - 8485 - 8990 - 9495 - 99100 - 104105 - 109110 - 114115 - 119120 - 124125 - 129130 - 134135 - 139140

28 MAC 401™ user manual8160 - 910 - 1415 - 1920 - 2425 - 2930 - 3435 - 3940 - 4445 - 4950 - 5455 - 5960 - 6465 - 6970 - 7475 - 7980 - 8485 - 8990 - 9

DMX protocols 299170 - 910 - 1415 - 1920 - 2425 - 2930 - 3435 - 3940 - 4445 - 4950 - 5455 - 5960 - 6465 - 6970 - 7475 - 7980 - 8485 - 8990 - 9495 - 9

Safety Information 3Safety InformationThe following symbols are used to identify important safety information on the product and in this manual:Warni

30 MAC 401™ user manual1 If DMX Reset is disabled in the onboard control menus, a reset command can only be executed if channel 2 is set to DMX value

DMX protocols 31DMX protocol, CT Zoom moduleCTCTXDMX Value Percent FunctionSnap/fadeDefaultDMX value110 - 1920 - 4950 - 6465 - 6970 - 8485 - 8990 - 1

32 MAC 401™ user manual—70 - 1920 - 3940 - 5960 - 189190 - 194195 - 199200 - 204205 - 209210 - 214215 - 219220 - 224225 - 229230 - 234235 - 239240 -

DMX protocols 338160 - 910 - 1415 - 1920 - 2425 - 2930 - 3435 - 3940 - 4445 - 4950 - 5455 - 5960 - 6465 - 6970 - 7475 - 7980 - 8485 - 8990 - 9495 - 9

1 If DMX Reset is disabled in the onboard control menus, a reset command can only be executed if channel 2 is set to DMX value 232 and channel 1 is se

LEE colors and RGB equivalents 35LEE colors and RGB equivalentsThe table below gives approximate RGB equivalents for the LEE colors available in the

36 MAC 401™ user manualOnboard control menusSingle head module operationWhen only one module is installed on the head, the HEAD menu is automatically

Onboard control menus 37FACTFACT LOADReturn all settings (except calibrations) to factory defaultsNB: can take up to 2 minutes to complete!CUS1, CUS2

38 MAC 401™ user manualDual head module operationWhen you install a second head module on the rear of the head, DUAL is automatically selected in the

Onboard control menus 39FRNT(continued)INFO(continued)AIRFTOTLCurrent elapsed time in hours since the air filter was cleaned or changed. Display the

4 MAC 401™ user manualPROTECTION FROM BURNS AND FIRE• Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C (104° F).• The exterio

40 MAC 401™ user manualREAR(continued)INFO(continued)PTMPCURRDisplay current average pixel PCB temperatureMSRDisplay highest pixel PCB temperature si

Onboard control menus 41PERS(continued)ERRMNORMDisplay errors at 100% intensity (regardless of DINT setting) and illuminate the service light.SLNTSil

42 MAC 401™ user manualAdjustment submenuThis menu is accessed under ADJ in the SERV service menu. Adjustments are for service use only.ADJRSETReset

Troubleshooting 43Troubleshooting Problem Probable cause(s) RemedyFixture is completely dead.No power to fixture. Check power and connections.Fuse bl

44 MAC 401™ user manualMAC 401 SpecificationsPhysicalLength . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

MAC 401 Specifications 45Installation Mounting points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

AccessoriesMAC 401™ RGB Zoom module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . P/N 91611325MAC 401™

www.martin.com • Olof Palmes Allé 18 • 8200 Aarhus N • DenmarkTel: +45 8740 0000 • Fax +45 8740 0010

ContentsDimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6 MAC 401™ user manualIntroductionThank you for selecting the MAC 401™, an intelligent LED-based moving head washlight fixture from Martin Profession

Connections panel 7Connections panelFigure 1: Connections panel overviewABCDEFGA – AC mains power input(Neutrik PowerCon)B – Fuseholder, mains fuse 1

8 MAC 401™ user manualAC powerWarning! Read “Safety Information” starting on page 3 before connecting the MAC 401 to AC mains power.For protection fr

AC power 9Attaching a cable to the male input connectorTo attach a power cable to the supplied input connector:1. Slide the bushing over the cable.2.